• Shake and incubate samples simultaneously
• Complete with shaking racks for 15ml and 50ml conical tubes
• Intelligent, digital control
• Broad temperature and speed range

Designed for simultaneous heating and mixing of small samples, the VorTemp 1550 is supplied with interchangeable platforms for standard 15ml and 50ml conical tubes. Maximum capacity is 8 x 50mL or 18 x 15mL. Temperature in the VorTemp 1550 is adjustable over a broad range, making the unit useful for a variety of applications, including bacterial cultures and digestions. Mechanical convection provides a uniform and stable environment within the chamber. The VorTemp 1550 may also be used in the cold room for subambient applications.

Shaking speed as well as acceleration rates are adjustable. Acceleration can be set to three different levels to protect delicate samples.

A microprocessor controls all parameters including temperature and timed operation. Self-diagnostic software continuously monitors the unit for proper temperature and shaking speed, alerting the user to any errors. Heating and shaking are controlled by feedback loops which precisely maintain chosen parameters, independent of load or voltage fluctuations.

The sturdy construction of the VorTemp 1550 gives it stability during high speed shaking. The chamber is insulated to maintain temperature and reduce operating noise.

 
Benchmark™ Orbi-Shaker™ CO2-MP
All Environment Shaker for Microplates

• Designed for use in CO₂ incubators and other extreme environments
• Remote controlled, adjust settings without exposing the chamber
• 3 mm orbit for thorough mixing of well plates
• Includes 6-position microplate platform

The Orbi-Shaker™ CO2-MP is designed for thorough mixing of microplates in extreme environments such as CO₂ incubators. It can withstand temperatures from 4° to 65°C and humidity levels up to 100%.

To extend the lifetime of the shaker, all the electronics are in a remote-control module that is placed outside the chamber. This has the added advantage of adjusting the shaker speed and time without opening the chamber door and disturbing the interior environment. The controller's thin, flat cord will not interfere with the door seal and the unit can magnetically mount to the outer housing of the incubator. A 6-position microplate platform is included and secures both standard or deep well plates.

Specifications
 

Speed Range	200 to 1200 rpm
Speed Increment	1 rpm
Orbit	3 mm
Timer	1 min. to 99 hr or continuous
Ambient Operating Temp.	+0°C to +65°C
Platform Size	13 x 12 in. | 33 x 30 cm
Load Capacity	6 x microplates
Dimensions	11.9 x 13.4 x 3.5 in. 30 x 34 x 9 cm
Weight	25 lbs (11.5kg)
Cord Length	60.5 in. | 154 cm
Electrical	115 or 230V 50-60Hz; 600W
Warranty	2 Years

 

• Exclusive SmartChek temperature control system
• Stackable design saves space
• Full range of accessories available
• Internal electrical outlet


A small footprint, compact, stackable design and expanded temperature range make the 211DS incubators ideal for molecular biology and general use. Its integral orbital shaker makes it highly versatile.

MIDSCI's exclusive SmartChek temperature control system guarantees precise temperature control. Mechanical convection maintains a stable temperature environment and provides quick recovery after opening the door. A safety thermostat is located on the back of the unit. The insulated door has a large, double glass observation panel and opens nearly 180° for easy access.

Two full and one half shelf are supplied with each incubator. A flat platform and predrilled flask platform (clamps sold separately) are available for the 211DS.

Internal electrical outlet allows using small equipment such as GyroMini or Mini LabRoller Rotator inside the chamber of the 211DS. 

The GCH-24 Hematocrit Centrifuge allows your lab to determine erythrocyte fractions in blood as well as micro solution separations using the included twenty-four (24) place capillary rotor. The included rotor lids enhance user safety and are easy to remove or replace.

Programming is simple with the backlit LCD display, intuitive control buttons and parameter adjustment knob. The timer will not count down until the programmed speed is reached, ensuring accurate results. Setpoint can be set by G-Force or RPM.

Features:

• Speed range of 200-14,000rpm, max. RCF 18,620 x G
• Independent control of speed and time
• Easy operation with intuitive menu and easy-to-read display
• Maintenance free brushless DC motor
• Pulse operation for quick spins
• Included hematocrit rotor: 24 capillary capacity, max. speed of 12,000rpm
• Optional tube rotor: 24 place 1.5/2mL capacity, max. speed of 14,000rpm
• Includes pulse operation (quick spin)

Advanced Features:

• Speed/RCF switch
• Short-time run function
• Audible alert function

Safety Functions:

• Door interlock
• Overspeed detector
• Over-temperature detector
• Automatic internal diagnosis
• Automatic rotor identification

Technical Data:

Hematocrit Centrifuge Accessories:

GCH-24-ROT-1.5-2:   Rotor for the GCH-24 Centrifuge, 24-Place for 1.5mL/2.0mL, 14000rpm max

GCM-24-AD2:  Rotor Adapters for GCM-12, GCM-24, GCH-24 for 0.2mL Tubes, 24/bag

GCM-24-AD5:  Rotor Adapters for GCM-12, GCM-24, GCH-24 for 0.5mL Tubes, 24/bag

Benchtop Incubated Shakers

Performance

• Temperature range:
• Ambient +5°C to 80°C for IST-3075 / 4075.
• Ambient -15°C (Min. 15) to 80°C for IST-3075R / 4075R.
• Competitive high shaking speed up to 500 rpm.
• Orbital shaking motion in 19mm diameter.
• Microprocessor PID control.
• Three-point temperature calibration / Automatic tuning.
• Wide speed range even with heavy workload.
• Equipped with a maintenance-free BLDC motor to generate smooth, quiet, uniform, and yet powerful shaking motion.
• Best effort run function intelligently manages its rpm to keep shaking even workload is out of its capacity.
• Automatic shaking speed adjustment in case of excessive workload such as unbalanced load placement, unusual vibrations caused from unstable floor or external shock.
• Pleasant test environment by the smooth acceleration and deceleration control.
• Smooth start and smooth stop function prevents chemical spills from flasks or test tubes.
• High-velocity fan ensures uniform temperature distribution and rapid thermal recovery after door open.
• Air-tight silicone door seal to provide excellent temperature uniformity

Convenience

• Intuitive touch screen LCD controller with easy icons and logical menus.
• Easy-set digital timer for shaking operation. (1 min. to 999 hr. 59 min.)
• Wide sample monitoring and convenient sample loading.
• Convenient sample monitoring without affecting inside environment thanks to the three-side transparent acryl lid with bright LED lamps.
• Gas spring lid supports providing smooth motion, soft opening and closing.
• Repetitive task can be easily performed as the platform stops where it starts.
• Stopping the shaking platform always at the same position is highly beneficial for automated dosing or sampling process.
• Corrosion resistance stainless steel interior.
• Built-in RS-232 port and USB port for external control and data collection.

Safety

• Automatic run after power interruption.
• Temperature and shaking speed deviation alarm.
• Over-current protection, Stalled platform check.
• Mechanical over-temperature protection device.
• Environment-friendly CFC-free refrigerant. (for IST-3075R / 4075R)
• Audible and visible open-door alarms.



• ITEM NO.	AAH23465U	AAH23565U	AAH23665U	AAH23765U
  MODEL NO.	IST-3075	IST-3075R	IST-4075	IST-4075R
  Temperature Range	Amb. +5 to 80°C /	Amb. -15 (Min. 15) to 80 /	Amb. +5 to 80°C /	Amb. -15 (Min. 15) to 80 /
  	Amb. +9 to 176°F	Amb. -27 (Min. 27) to 176	Amb. +9 to 176°F	Amb. -27 (Min. 27) to 176
  Temp. Fluctuation at 37°C in flask	± 0.1°C / 0.18°F
  Temp. Variation at 37°C in flask	± 0.5°C / 0.90°F
  Refrigerator (Hp)	-	1 / 6 HBP	-	1 / 6 HBP
  Motion type	Orbital
  Amplitude size (dia.)	19.1mm / 0.75in
  Speed range (RPM)	20 to 500rpm
  Accuracy	±1% of set speed (>100rpm) / ±1 (100rpm)
  Timer	1 min. to 999 hr 59 min.
  Max. load	10kg / 22lbs at 500 rpm		14kg / 30.9lbs at 500 rpm
  	15kg / 33.1lbs at 400 rpm		21kg / 46.3lbs at 400 rpm
  Volume	53L / 1.9 CuFt		83L / 2.9 CuFt
  Platform (W×D)	350×350mm / 13.8×13.8in		450×450mm / 17.7×17.7in
  Interior (W×D×H)	410×410×320mm / 16.1×16.1×12.6in		510×510×320mm / 20.1×20.1×12.6in
  Exterior (W×D×H)	440x785x510mm / 17.3x30.9x20.1in		540x 890 x510mm / 21.3x35x20.1in
  Net weight	65kg / 143.3lbs	73kg / 160.9lbs	81kg / 178.6lbs	90kg / 198.4lbs
  Electrical requirements (120V)	60Hz, 7.5A	60Hz, 10.1A	60Hz, 7.5A	60Hz, 10.1A

• Exclusive SmartChek temperature control system
• Stackable design saves space
• Full range of accessories available
• Internal electrical outlet


A small footprint, compact, stackable design and expanded temperature range make the 211DS incubators ideal for molecular biology and general use. Its integral orbital shaker makes it highly versatile.

MIDSCI's exclusive SmartChek temperature control system guarantees precise temperature control. Mechanical convection maintains a stable temperature environment and provides quick recovery after opening the door. A safety thermostat is located on the back of the unit. The insulated door has a large, double glass observation panel and opens nearly 180° for easy access.

Two full and one half shelf are supplied with each incubator. A flat platform and predrilled flask platform (clamps sold separately) are available for the 211DS.

Internal electrical outlet allows using small equipment such as GyroMini or Mini LabRoller Rotator inside the chamber of the 211DS. 

Shaking features

• Select between orbital or reciprocating action.
  
• Speed range: 10 to 300 rpm.
  
• Programmable shaking motion.
  
• Run time: 10 sec to 999 hr 59 min 59 sec.
  
• Forward & Backward, Pause: 10 sec to 59 min 59 sec
  
• Maximum orbit size: 40mm dia. (1.6❠dia.)
  

  Operating features

• +5°C above room temperature to 60°C for SI-300, 600
  
• 15°C to 60°C for SI-300R, 600R
  
• Microprocess PID control/ Auto-tuning/ Calibration.
  
• Digital timer: 1 min to 99 hr 59 min, delayed ON/ OFF.
  
• Over-temperature limiter/ Door opening alarm.
  
• Digital LED display for temperature (0.1°C resolution), speed, and shaking motions.
  
• Preset 3 most commonly used temperature settings.
  
• 9 step temperature and up to 200 cycles of repetition programmable for each profile.
  
• Adjustable 3 step fan speed.
  
• RS-232 interface available.
  

  Constructional features

• Brushless DC motor for long maintenance-free use.
  
• High-velocity fans ensure rapid thermal recovery and excellent variation. 
  
• Gas spring door and lid guards against sudden closures.
  
• Acryl lid and inner lamp functions allow observation of flask contents. 
  
• Attached fluorescent lamp offered bright observation in a chamber. 
  
• Use CFC-free refrigerant (for SI-300R, 600R)

Specifications

SB-12L Shaking Water Bath

• Orbital shaking motion
• Included spring platform accepts tubes, bottles, and flasks
• Digital control of time, temperature, and speed
• Compact design, conserves benchspace

The compact shaking water bath utilizes the well proven, belt-less motor drive system, with the addition of precision temperature control up to 80°C. The seamless, stainless steel chamber has a 12 liter capacity and includes a universal spring loaded platform for securing 15 and 50 mL test tubes, as well as Erlenmeyer flasks and media bottles up to 1 liter. A hinged and removable lid is also included to reduce energy waste, prevent splashing and divert condensation away from samples.

Easy to use controls allow the user to digitally select and monitor time, temperature, and shaking speed, while a constant monitoring system ensures accuracy over each parameter.
 
Specifications 

Shaking Water Baths
 
Operating features

• +5°C above room temperature
• Microprocess PID control / automatic tuning / calibration
• Digital timer for delayed ON/OFF: 1 min to 99 hr 59 min
• Protection against over-temperature
• Digital LED display (0.1°C/ 1 rpm resolution)
• Splash-proof keypad
• Warranty: 18 months standard; 6 additional months upon receipt of warranty card

Constructional features

• Separate control keys for shaker mechanism allowing the unit also to be used as a constant temperature bath
  
• Minimal shock to the samples thanks to the shaker's gentle start feature
  
• Multiple LED displays for setting various values
  
• Isolated design of agitator, heater, and sensor by a baffle plate to minimize the turbulence in the bath fluid and also to protect users and samples against direct contact
  
• Removable shaking carriage designed for external assembly avoiding direct contact with the bath fluid
  
• Minimization of the liquid loss and dripping of the bath liquid into the samples thanks to the included gable cover
  
• Included SUS 304 spring wire rack with double-two-tier providing various ways of glassware settings
  

 

Model		BS-06	BS-11	BS-21	BS-31
Bath Volume		17 L 0.6 Cu Ft	25 L 0.9 Cu Ft	37 L 1.3 Cu Ft	55 L 1.9 Cu Ft
Working Temperature Range		Ambient +5°C to 100°C | Ambient +9°F to 212°F
Temperature Stability*		± 0.2°C | ± 0.36°F
Shaking System	Motion / Speed Range	Reciprocating | 20 to 180 RPM
	Reciprocating Stroke Length	25, 30, 35 mm | 1.0, 1.2, 1.4 in. Available - Standard 30 / 12
Dimensions	Bath Opening / Depth  (W x L, D)	109 x 243, 235 mm  4.3 x 9.6, 9.3 in.	229 x 243, 235 mm 9.0 x 9.6, 9.3 in.	389 x 243, 235 mm 15.3 x 9.6, 9.3 in.	670 x 350, 235 mm 26.4 x 13.8, 9.3 in.
	Overall (W x L x H)	430 x 440 x 355 mm 16.9 x 17.3 x 14 in.	550 x 440 x 355  mm 21.7 x 17.3 x 14 in.	710 x 440 x 355 mm  28 x 17.3 x 14.3 in.	860 x 490 x 355 mm 33.9x19.3x14.0 in.
	Net Weight	26 kg 57 lbs	30 kg 66 lbs	35 kg 77 lbs	42 kg 93 lbs
Round Flask Maximum Mounting Amount in Spring Wire Rack	50 mL	5	16	22	38
	100 mL	3	9	15	22
	250 mL	2	5	8	14
	500 mL	2	4	6	8
	1 L	-	2	3	6
	2 L	-	1	2	3
Maximum Mountable Flask Clamps w/ Universal Platform	50 mL	9	12	20	32
	100 mL	3	9	15	24
	250 mL	2	4	8	12
	300 mL	2	4	8	12
	500 mL	2	4	6	12
	1 L	1	2	4	6
	2 L**	-	1	2	3
	2.8 L**	-	1	1	2
Electrical Requirements (230V,60Hz)***				8.9A	8.9A
Cat. No.				AAH44211K	AAH44311K
Electrical Requirements (230 V, 50 Hz)***				8.9 A	8.9 A
Cat. No.				AAH44212K	AAH44312K
Electrical Requirements (120 V, 60 Hz)		7.1 A	8.8 A
Cat. No.		AAH44063U	AAH44113U

* Technical data (according to DIN 12876)
** 2 and 2.8 L flasks must by opening the bath cover
*** BS-21,31 are provided ONLY for 230 voltage


Ordering Information

AAH44063U	BS-06 Shaking Water Bath with Spring Wire Rack, 17 L / 0.6 Cu Ft, 120 V
AAH44113U	BS-11 Shaking Water Bath with Spring Wire Rack, 25 L / 0.9 Cu Ft, 120 V
AAH44212K	BS-21 Shaking Water Bath with Spring Wire Rack, 37 L / 1.3 Cu Ft., 230 V/50 Hz
AAH44211K	BS-21 Shaking Water Bath with Spring Wire Rack, 37 L / 1.3 Cu Ft, 230 V/60 Hz
AAH44312K	BS-31 Shaking Water Bath with Spring Wire Rack, 55.52 L / 1.961 Cu Ft, 230 V/50 Hz
AAH44311K	BS-31 Shaking Water Bath with Spring Wire Rack, 55.52 L / 1.961 Cu Ft, 230 V/60 Hz
AAA44521	Universal Platform for BS-06 Shaking Water Bath
AAA44522	Universal Platform for BS-11 Shaking Water Bath
AAA44523	Universal Platform for BS-21 Shaking Water Bath
AAA44524	Universal Platform for BS-31 Shaking Water Bath

Operating features

• 5°C above room temperature to 150°C.
  
• Microprocessor PID control / Auto-tuning / Calibration.
  
• Digital timer : 1 min to 99 hr 59 min, delayed ON / OFF.
  
• Over-temperature limit and low fluid level protection.
  
• Conveniently preset 3 most commonly used temperature settings, without auto-tuning.
  
• Digital LED display (0.1°C resolution) with splash-proof keypads.
  
• RS-232 interface available.
• 18 months standard; 6 addiitionl months upon receipt of warranty card
  

  Constructional features

• Variable-speed pump for liquid viscosity for accurate, stable, and efficient temperature 
  management. (1 to 3 steps of pump for internal circulation / 4 and 5 steps for external circulation)
  
• Powerful pressure and suction pumps provide contrast pressure and flow rate throughout the 
  whole temperature range.
  
• Baffle plate screens circulating pump, heater and sensor to minimize shaking bath fluids and protect sample 
  and operators from direct contact.
  
• Dry-running protection; automated heating element cut-off and audible and visual warning.
  
• Seamless stainless steel tank with a reservoir drain that resists corrosion and make cleaning easy.
  
• Space saving design uses minimal bench space.

   

  Model   CW-10G CW-20G CW-30G Bath volume (L/cu ft)   10.0 / 0.4 20.0 / 0.7 30.0 / 1.1 Working Temperature Range2)(°C/°F)   Temperature Stability 1)(±°C/°F)   0.05 / 0.09 0.1 / 0.18 0.1 / 0.18 Pump Max. pressure, max. flow rate 5.9 PSI (406.8 millibar), 7.4 gallons/minute (28.0 liters/minute) Max. suction flow rate 2.6 gallons/minute (10.0 liters/minute) Dimensions Bath opening/ depth  (WxL, D) (mm/inch)   211x154, 180 / 8.3x6.1, 7.1 290x214, 200 / 11.4x8.4, 7.9 300x264, 230 / 11.8x10.4, 9.0 Overall  (WxLxH)(mm/inch)   281x450x444 / 11.1x17.7x17.5 360x510x464 / 14.2x20.1x18.3 370x560x494 / 14.6x22.0x19.4 Net weight(kg/lbs)   15.0 / 33.0 17.5 / 38.6 19.5 / 43.0 Electrical Requirements (230V, 60Hz)   50/60Hz, 6.7A 50/60Hz, 8.8A 50/60Hz, 8.8A Cat. No.   AAH52315K AAH52325K AAH52335K Electrical Requirements  (120V, 50Hz)   50/60Hz, 8.6A 50/60Hz, 8.6A 50/60Hz, 8.6A Cat. No.   AAH52316U AAH52326U AAH52336U

  1) If you operate the unit in 1 to 3 steps of pump, the temperature range can be from Amb. +5°C but in 4 and 
  5 steps, the range will be from Amb. +15°C.
  2) The heat-up time is measured on a 230V electrical condition with 1000W heater power.

   

Circulating Water Bath
 
SHEL LAB Circulating Water Baths are an excellent choice for research and quality control applications. They are highly accurate, easy-to-use, rugged and safe. Features include:

• Microprocessor Control
• Easy-To-Clean Polymer-Coated Tanks
• Air Jacket Heating Eliminates Hot Spots
• Recessed Heating Element Prevents Burnout
• 2 year limited warranty, excludes tank

The stainless steel cover is included with the purchase of this model. The use of covers is suggested since they allow maximum temperature range and help maintain better temperature uniformity.